Ads Top

What Is a Nuclear Reaction?

A nuclear reaction is at its most basic nothing more than a reaction process that occurs in an atomic nucleus. They typically take place when a nucleus of an atom gets smacked by either a subatomic particle (usually a "free neutron," a short-lived neutron not bound to an existing nucleus) or another nucleus. That reaction produces atomic and subatomic products different from either of the original two particles. To make the kind of nuclear reaction we want, a fission reaction (in which the nucleus splits apart), those two original particles have to be of a certain type: One has to be a very heavy elemental isotope, typically some form of uranium or plutonium, and the other has to be a very light "free neutron." The uranium or plutonium isotopes are referred to as "fissile," which means we can use them to induce fission by bombarding them with free neutrons. In a fission reaction, the light particle (the free neutron) collides with the heavy particle (the uranium or plutonium isotope) which splits into two or three pieces. That fission produces a ton of energy in the form of both kinetic energy and electromagnetic radiation. Those new pieces include two new nuclei (byproducts), some photons (gamma rays), but also some more free neutrons, which is the key that makes nuclear fission a good candidate to generate energy. Those newly produced free neutrons zoom around and smack into more uranium or plutonium isotopes, which in turn produces more energy and more free neutrons, and the whole thing keeps going that way--a nuclear fission chain reaction. Nuclear fission produces insane amounts of energy--we're talking several million times more energy than you'd get from a similar mass of a more everyday fuel like gasoline. Getting Usable Energy From Fission There are several types of nuclear fission reactors in Japan, but we're going to focus on the Fukushima Naiishi plant, probably the most hard-hit facility in the country. Fukushima, run by the Tokyo Electric Power Company (TEPCO), has six separate reactor units, although numbers 4, 5, and 6 were shut down for maintenance at the time of the earthquake (and more importantly, the subsequent tsunami). Numbers 1, 2, and 3 are all "Boiling Water Reactors," made by General Electric in the early- to mid-1970s. A Boiling Water Reactor, or BWR, is the second-most-common reactor type in the world. A BWR contains thousands of thin, straw-like tubes 12 feet in length, known as fuel rods, that in the case of Fukushima are made of a zirconium alloy. Inside those fuel rods is sealed the actual fuel, little ceramic pellets of uranium oxide. The fuel rods are bundled together in the core of the reactor. During a nuclear fission chain reaction, the tubes heat up to extremely high temperatures, and the way to keep them safe turns out to also be the way to extract useful energy from them. The rods are kept submerged in demineralized water, which serves as a coolant. The water is kept in a pressurized containment vessel so it has a boiling point of around 550 °F. The burning hot fuel rods turn the water to steam, which is actually what we want from this whole complicated arrangement--the high-pressure steam is used to turn the turbines on dynamos, producing electricity. Boiling Water Reactor Schematic: 1. Reactor pressure vessel (RPV) 2. Nuclear fuel element 3. Control rods 4. Circulation pumps 5. Engine control rods 6. Steam 7. Feedwater 8. High pressure turbine (HPT) 9. Low pressure turbine 10. Generator 11. Exciter 12. Condenser 13. Coolant 14. Pre-heater 15. Feedwater pump 16. Cold water pump 17. Concrete enclosure 18. Mains connection Nicolas Lardot - Wikimedia Commons Safety Since lots of heat is being produced, as well as the production and use of lots of pretty nasty radioactive materials, the engineers have implemented several safety efforts beyond simply the use of the cooling water. The plant's core, the fuel rods and the water, is encased in a steel reactor vessel. That reactor vessel is in turn encased in a giant reinforced concrete shell, which is designed to prevent any radioactive gases from escaping. There's typically a system of control rods in a functional fission plant, essentially structures that control the rate of fission by absorbing the roaming free neutrons, but those aren't of much use now. In Fukushima's reactors, the control rods were used to shut down the fission reaction, which they did correctly, but they've exhausted their use now. But there are still some vulnerabilities, both mechanical and chemical, that the earthquake and tsunami exploited in the Fukushima plant. Is There an "Off" Switch? Sure! But it's not as effective as unplugging a rogue kitchen appliance, mostly due to some chemical reactions inherent in the fission reaction--you need to keep certain certain precautions active, notably cooling, even after the plant has been "shut off." At the onset of the earthquake, the plant automatically shut down the fission process, which normally would leave the coolant system--both the main one and a backup generator--still operational. But the tsunami wiped out power to the plant, which took down the main coolant system, and a wave destroyed the diesel-based backup system. Even though the fission had stopped, coolant is still very much required to keep the plant safe. That's due to the heat that remains in the nuclear core, both from the recently-disabled but still-hot fuel rods and from the various byproducts of the fission process. Those byproducts include radioactive iodine and caesium, both of which produce what's called "decay heat"--essentially residual heat that very slowly dissipates. If the core isn't continuously cooled, there's still enough heat that can still cause a meltdown even after it's been "turned off." In the case of the Fukushima plant, with both the main and backup coolant systems down for the count, TEPCO was forced to rig a method to flood the core with seawater laced with boric acid (the boric acid to stave off another fission reaction if one were to restart due to a meltdown--more on that below). That's a bad sign--it's a last-ditch effort to prevent a meltdown, as the salt in the seawater will corrode the machinery. It's also a temporary fix: TEPCO will need to pump thousands of gallons of seawater into the core every day, until they can get the coolant system back online. Without it, the seawater method might have to go on for weeks, even up to a year, as the decay heat subsides. The Dreaded Meltdown First of all, a "meltdown" is not a precisely defined term, which makes it fairly useless as an indicator of what's going on. Even the terms "full meltdown" and "partial meltdown" are pretty unhelpful, which is partly why we've written this guide--you'll be able to understand what's actually happening without relying on spurious terms that the experts themselves are often loathe to use. Anyway, let's start at some of the less severe (though still unsettling) things that can happen when the coolant liquid is no longer present in the core. When the fuel rods are left uncovered by water, they'll get far too hot--we're talking thousands of degrees Celsius here--and begin to oxidize, or rust. That oxidation will react with the water that's left, producing highly explosive hydrogen gas. This has already happened in Unit 1 at Fukushima (see the video below). The hydrogen gas can be vented in smallish doses into the containment building, but if they can't vent it fast enough, it'll explode, which is exactly what happened at Unit 1. Keep in mind, this is not a nuclear reaction, but a simple chemical explosion that often (as in this case) results in little or no radioactive material being leaked into the outside world. (TEPCO has announced that after the explosion, radiation levels in the area around the plant were still within "normal" parameters.) This is an important distinction--not to say that a hydrogen explosion at a nuclear plant is particularly fun news, but it is not nearly as panic-inducing as a nuclear explosion. part 2

No comments:

Silahkan isi komentar anda disini..!

Powered by Blogger.